Accessories
Odds and ends that are needed on race day
$0.50
Euro Style numbers. Numbers are sold individually. Example... If the number that you want is 37, order a 3 and a 7. Numbers are 5 inches high. Simply place graphic in desired position, smooth out with the edge of a credit card, remove transfer film and you're ready to go. Available...
$3.00
7” X 10” flexible plastic number panel. Available in Black, Blue, Orange, Red, White, or Yellow.
$15.00
This kit solves the common problem of how best to attach fuel line to your chassis. When using just a tie-wrap, you risk squeezing the fuel line too tightly resulting in it being crushed. If you don’t tighten it enough, the fuel line will drag on the track surface. This...
from $9.75
Formulated with the purest degummed castor base oils available and blended with the most advanced additives to eliminate ring sticking, reduce carbon & varnish formation. Provides protect against rust & corrosion. Helps eliminate sparkplug fouling. Burris Hi-Rev Castor is the ideal lubricant for gasoline, alcohol and nitro fuels. Buy it by...
$1.00
Vinyl stick on number panel for the side of your kart.
7 1/4" Tall by 8 7/8" Wide
Available in White or Yellow
Sold Individually - Order two if you need both sides of your kart
$2.00
Vinyl stick on number panel for the front driver fairing.
9 3/4" Tall by 8 1/2" Wide
Available in White or Yellow
$6.75
This cable clamp is tapered on each end so they do not catch on a driver suit or shoe. Fits both throttle and brake cables.
Finished in black anodizing and uses 2 flat point set screws.
Clamp measures 1 1/8" long by 3/8".
$11.00
Protect you or your driver from a potential accident by using a chain guard. Fits the Lo 206 engine. Measures 8-1/2" x 2-1/2". Designed to fit Briggs, Clone, Tecumseh and Honda. No bolts / washers included. Chain covers are designed to deflect broken chain to the ground instead of up...
$0.50
Block Style numbers. Numbers are 5 inches high. Numbers are sold individually. Example... If the number that you want is 58, order a 5 and a 8. Simply place graphic in desired position, smooth out with the edge of a credit card, remove transfer film and you're ready to go. Available...
from $45.00
Replacement shafts for Burris Mini Lite Starters. 103-RH-2 This is a 2-cycle replacement drive 5/16" hex tip with 1/2" square. This shaft is for the starter motors with the splined end on the output shaft. I.D of shaft is stepped .530" X .500. 103-RH-4 This is a 4-cycle replacement drive...
$265.00
The Burris Mini-Lite self-contained starter packs a lot of power into a small package. The anodized billet aluminum frame houses the high torque gear reduction motor and the sealed lead acid battery into a unit that weighs less than 18 lbs. The Burris Mini-Lite has been used successfully on Yamaha,...
from $20.00
Chain tools for #35, #219, and #428 chain. The steel construction allows for fast, easy removal and installation of pins.
The #428 Chain Tool also works for #40 and #41 Chain
from $8.00
Formulated with the purest degummed castor base oils available and blended with the most advanced additives to eliminate ring sticking, reduce carbon & varnish formation. Provides protect against rust & corrosion. Helps eliminate sparkplug fouling. Burris Hi-Rev Castor is the ideal lubricant for gasoline, alcohol and nitro fuels. Buy it by...
from $6.00
Pins break every once in awhile... and it's going to happen when you least expect it. It's a good idea to have a spare on hand.
